Welding Gas Tank Forum

I need to get a high pressure fuel pump to my system. Put the hole up.

Pin On Projects

Cut many lids off of race gas 55 gallon drums.

Welding gas tank forum. _____ My Webby Tefs-tQ loads of stuff about my bikes my Land-Rovers and the stuff I do with them. People have been killed and seriously injured by such. Tank is made fromNot that it matters.

Hi all The restoration of my 29 continues and Ive turned to the gas tank. Shake the hell out of it turning the tank a little bit at a time as you do it. Topic Welding Industry General Welding Discussion Welding a fuel tank By WasntMe Date 01-29-2007 0052 I have a couple of motorcycle fuel tanks that I need to weld a bung onto.

The typical transaction at a welding shop consists of dropping off an empty cylinder at the tank farm walk into the shop or. Gunner asked me to get some wet towels to wrap around the weld. About 20 miniutes of this will have all the fuel residue vapours cleared out.

I can either get an external inline pump or to do it the trick way of holesawing the top off of my original tank and installing the intank pump off of my donor vehicle. Years ago I was welding a gas tank on my grain truck so I had it off the truck and filled with water a garden hose from the hydrant the hydrant was set to keep the tank full and over flowing but just a trickle well the wife walks by and shuts off the hydrant as she didnt want me to waste water of corse the garden hose started siphoning the tank dry well that started a series of small. Quarter fill your tank with boiling water a generous amount of dish washing liquid and a hand full of gravel.

You can use any inert gas to keep the vapors from collecting in the fuel cell. Short of dropping the tank and welding it does anyone have a bright idea as to how to. It appears to have a pretty serious leak at the top of the tank where the tank meets the fire wall segment.

Called Gunner a welder and he came told the rodder to fill the tank full to the top no air. 06-30-2020 1205 PM. Then the water wont drain out.

A hot rodder late one Sunday night had a leaking gas tank at the filler neck. That way you can be safe. My main project at the moment is converting my truck over to EFI from carb.

Most car tanks located at the rear are fairly easy to remove. 3 Aug 8 2007. To remove the fumes from the gas tank insert small pieces or pellets of dry ice into the filler neck of the tank.

Im not a welder. HE HE into the fuel tank allow it run a few minutes and then weld as the car is running and pushing in the exhaust into the tank. Is used on a tank or drum containing flammable material solid liquid or vapour the tank or drum can explode violently.

Step 4 - Dive In. I need to know what is the. Not logged in American Welding Society Forum.

Fuel tanks that need to be welded on should be thouroughly cleaned with soap and water and should be fully purged with an inert gas before welding. Forum AWS Website Help Search Login. Tanks and drums that are empty usually still have.

Even with water you will have to be real careful to make sure the tank is COMPLETELY full of water. Being that is is a fuel oil tank like diesel fuel that will put out a match and wont light with a torch on the ground nowadays just weld it. Home Forums Drivetrain Performance High Performance Modifications welding sump on stock gas tank Discussion in High Performance Modifications started by nova75mike May 28 2008.

Before welding wash out your fuel tank with warm soapy water then rinse with clear water. OW the trapped gas vapors can still explode if you burn into a pocket. He was known throughout Phoenix for this type work and had been doing it for over 30 years.

O8k Jun 10 2009. This should remove fuel residue. Page 1 of 3 1 2 3 Next May 28 2008 1.

Broncobowsher Solo Diver. When I ran my weld shop repairing gasfuel tanks was a common job and we simply dipped them in our cleaning tank same as the radiator shop then as an added measure of safety we either purged them with CO2 or filled them with water depending on the situation I have seen quite a few welded simply after the tank dip and we never had any problems at all. A forum community dedicated to Jockey motorcycle owners and enthusiasts.

So a few days before the attempt I gave the tank a thorough rinse and left it in the sun to dry. Personally saw a top fuel dragster nitro methane tank get tigged. Residues in the bottom and in seams and crevices.

Next youll need to remove all traces of flammable gasoline fumes. Similarly I recall on WWII Bomber-planes the engines exhaust was ducted into the fuel tanks in the wings. When welding car fuel tanks I run a shop vac hose from a tailpipe of a car not from the car that the tank goes to another car.

Just fill with water to the top no vapor. He asked if we knew someone who could weld it. Welding Gas Tank.

Buying gasses at a welding shop is a bit different than getting scuba tanks filled. Just stuck the truck exhaust into the tank. My Neighbors Motorcycle Gas Tank supplier was killed a few years back from welding Gas tank for a motorcycle.

That tank is steel and I could weld it with mig or tig. Can anyone recommend a shop that i can ship the tank to or to a DIY fix that doesnt require welding. He was a well respected authority on how to do it safely and was considered an expert at the task.

Anything less than that is just plain haphazard. Purging with exhaust fumes is plain stupid because exhaust fumes still contain flammable gases from un-burnt fuel. Flush the tank with clean water afterwards to.

The extra effort outweighs the risk. One trick I read during the research was to rinse the tank with acetone to remove fuel residue and make the plastic weld go better. The carbon di-oxide worked like a welding mask gas to help prevent the fuel vapor reaching flash-point.

IMHO anytime you are welding above a tank take it out. My favorite is bleed Argon it the tank after it is drained of fuel or have a professional fuel drainer clean the tank first. Thanks for all the help on the starter issue now On to a new issue our fuel tank leaks around the drain plug in the bottom of the tank of course it had to be the very bottom It is the weld not the plug.

If a welding blowpipe or burner.

Pin On Shop Carts

Image Result For Gas Welding Cart Plans Welding Cart Welding Projects Welding Cart Plans

Google Image Result For Https Www Mig Welding Co Uk Forum Data Attachments 9 9297 912efb92015977a92f36725 Gas Bottle Wood Burner Metal Garden Art Wood Burner