Welding And Cutting Jsa

Heights and Crane Usage JSA Preparation Project. Oxy-Acetylene welding used on average X times a day X days a week by X of welders.

Job Safety Analysis Form Hazard Analysis Job Analysis Task Analysis

Aerosol spray cans-lubricants etc from the welding.

Welding and cutting jsa. JSA for Welding operations sample WORK LOCATION ROOM NO. Allow material to cool on workbench. Burn to hands or fingers Wear glove.

A JSA is an effective procedure to identify hazards associated with welding cutting or brazing tasks and can help put in place effective safety controls. Pinch to fingers Keep fingers away from pinch points. Sparking Damage cable Page.

Welding shall be cleared and marked as a Do Not Enter Zone to protect any workers passing underneath from being hit by sparks or slag. Place welding shield flash barrier in position to shield outsiders from flashing and to prevent sparks and other potential ignition sources. A fire watch must be maintained at least 30 minutes after the hot work is completed.

Argon Cylinder near the Hot Work areaKeep oxy acetylene cylinders at least 5 meters away from. JSA for Welding Cutting grinding JSA for welding of HVAC Pipes JSA for the fixing embedded Plate JSA for operation of jack hammering on generator footing JSA for J mobilization of crane welding cutting and grinding and Air Blowing of spools in process area JSA for mobilization of crane erection of spools and welding cutting and grinding and tie in on existing spools. Job Area JSA Number.

Set up Welding Cutting 51 Weld Leads present tripping Hazard 511 Keep Leads out of heavy traveled areas Equipment 512 Elevate Leads where possible 52 Leads Grounding out and sparking 521 Insure Leads are in good condition with no bare wire exposed or cuts 522 Protect Leads from damage while laying on ground as much as possible. Job Safety Analysis is a termed as JSA and it is defined as the procedure of analyzing the job for the purpose of finding hazards in each steps and developing the safety precautions to be adopted. Installation of Staircase and Hand Rails Welding Site Location.

UV rays Wear proper PPE for welding ie leather jackets Gloves welding goggleswelding mask Trained Fire Watch. - Inspect arc welding equipment cables and connections. Look for loose connections frayed insulation on electrode holders and cables see photo make sure electrical.

Flashing sparks slag splatter Wear welding hood welding jacket apron gloves and work shoes. Combustible material must be screened from slag heat and sparks. HAZARD IDENTIFICATION Identify hazards that.

Description of Task Step Control Measures Preventive Measures Hazard Electrocution Spatter burns Damage cable Hot tabs end pieces of welding rods. Step Description Hazards Control Measures Responsible Person 1 Cutting Welding and Grinding Sparks Hot Slag Open Flame Electricity Gas Hot Surfaces Contain your sparks as far as possible screen off Direct your sparks away from others Remove all combustibles Have fire extinguisher at hand when grinding Contain your slag as far as possible Barricade area below when welding. While there are a number of forms and permits which help workers get approval to start and execute work safely there also needs to be some pre-welding and cutting.

Welding and cutting operations can be dangerous activities even when safety is a priority and managed properly. Flush Lines prior to cutting welding and grinding. The following instructions and work.

This job safety analysis for welding and cutting sample can be used as a template or used as an example for your own welding and cutting JSAs. This JSA technique can be applied at any stages of process activities and it. Weldingcutting operations shall be performed by trained certified workers.

Haji Noor Muhammd Haider Ali Imtiaz HameedLIST ASSOCIATED PROCEDURESWORK INSTRUCTIONS OR TEMPORARY. Establish safety diameter around weld area approx. Insert arc welding rod in handle.

JOB TITLE AIM. Jsa for erection of structure piping including lifting welding grinding and cutting Air BlowingJSA DATE. Not cleaning area could leave dust particlescombustibles that could flare.

This Procedure provides safety and health instructions regarding gas and electric welding cutting brazing or similar flame or spark-producing operations to protect personnel and property against heat evolved gases and fumes electrical shock and radiation. Use this template to identify and observe each job step capture any hazards and provide a recommended elimination or control measure. Inspect the cylinders hoses before starting the job Before starting welding make sure the area is clear of all types of combustible materials Provide a fire blanket on site Make sure fire extinguishers are available on site Supervisor Workers.

Compressed gas cylinders shall be separated from flammable or combustible material by at least 35 feet. Grinding Welding Gas cutting Step No. Falling of SparksEnclose the welding area through tarpaulin.

Damaged or leaking cylinders or hoses. Follow hot work procedures fire extinguisher gas testing cover drains use fire spotter assess welding habitat. Remove remainder of arc welding rod if any.

Remove flammable materials eg. Chalk mark welded area Hot 7. Wipe down work area with damp cloth water Spilling water could cause sliptrip.

Flash Back Fire Provide a check valve flash back arrester between oxy-acetylene hose gas regulator. Sign in and inspect Step 1 - WeldingCuttingBurning Equipment - Wires cables hoses - Before setting up the welding shop visit the Admin desk to sign in. WELDING AND CUTTING SAFETY PROCEDURE.

Confined Space Definition Entry Working Procedure Method Statement Hq In 2021 Space Definition Confined Space Emergency Response

Pin On Hse Documents Free Download

Find Out How You Can Help Your Students Prepare For The Rigorous New Parcc Assessment For More Information Contact Gina Hare With Parcc School Help Teachers