Jsa For Welding Cutting And Grinding

Grinding Welding Gas cutting Step No. Pinch to fingers Keep fingers away from pinch points.

Pin On Main Gate Design

Check cord integrity condition of grinding wheel and appropriate RPM.

Jsa for welding cutting and grinding. Only experienced personnel to use the equipment. PERSONAL PROTECTIVE EQUIPMENT TOOLS. GC - Work Area Equipment.

Hand injury from inadvertent starting Verify the guard is tight and appropriate for the job. Set up Welding Cutting 51 Weld Leads present tripping Hazard 511 Keep Leads out of heavy traveled areas Equipment 512 Elevate Leads where possible 52 Leads Grounding out and sparking 521 Insure Leads are in good condition with no bare wire exposed or cuts 522 Protect Leads from damage while laying on ground as much as possible. Unit that consists of measuring cutting grinding fit-up welding blasting painting and packing.

Now undertake the JSA and record in the table below. Hard Hat Safety Shoes Apron Welding Hood Safety Goggles Hand Gloves Multi Gas Detector SEQUENCE OF BASIC JOB STEPS POTENTIAL HAZARDS Yes No. JSA KOC 05 Facility.

Inspect the trigger for physical damage and proper operation. Verify that the guard is tight and appropriate for the job. Check conditions of grinding wheel and appropriate RPM.

Installation of Staircase and Hand Rails Welding Heights and Crane UsageJSA Number. Remove remainder of arc welding rod if any. Ad China Sale Welding Machine.

Burn to hands or fingers Wear glove. Periodical checking and maintenance of all power tools. Haji Noor Muhammd Haider Ali Imtiaz HameedLIST ASSOCIATED PROCEDURESWORK INSTRUCTIONS OR TEMPORARY.

Spark containment to be used. Control Measures Preventive Measures. Use prompts on JSA Prompt Sheet and Hazard Checklist PA-HSEC-02-040-002-F03.

Follow hot work procedures fire extinguisher gas testing. 3 4 Description of Task Step Gas Cutting Welding Control Measures Preventive Measures Hazard High Pressure air Flying objecteye injuries Page. All electrical cords shall be inspected and in good working condition prior to use no missing ground pins no damaged cords or frayed wires evident.

Jsa for erection of structure piping including lifting welding grinding and cutting Air BlowingJSA DATE. Employed a JSA Job Safety Analysis instrument sheet to facilitate the process of. Look for loose connections frayed insulation on electrode holders and cables see photo make sure electrical.

Sign in and inspect Step 1 - WeldingCuttingBurning Equipment - Wires cables hoses - Before setting up the welding shop visit the Admin desk to sign in. ARC WELDING CUTTING GRINDING JSA Ref. Compressed gas cylinders shall be separated from flammable or combustible material by at least 35 feet.

JOB SAFET ANALYSIS Grinding Welding Gas cutting. Insert arc welding rod in handle. Combustible material must be screened from slag heat and sparks.

Given that many jobs are done in the fabrication unit there are many hazards and risk sources that can cause. Trusted China Suppliers Verified by SGS. Wear a face shield while grinding Make sure an eye wash station is available nearby 2 of 3.

Grinding and welding area contains sparks by. Safety Goggles Face Shield to worn by all workers during welding cutting activity. Trusted China Suppliers Verified by SGS.

Verify the appropriate handle location. Check grinding wheel tightness. - Inspect arc welding equipment cables and connections.

Flashing sparks slag splatter Wear welding hood welding jacket apron gloves and work shoes. Do not plug in the machine until inspection is complete. JOB TITLE AIM.

Description of Task Step. Flush Lines prior to cutting welding and grinding. Hand injury from inadvertent starting Do not plug in the machine until inspection is complete.

Only experienced personnel to use the equipment. Spark containment to be used. Foot injury from dropping the tool Rest the tool on the bench.

Check grinding wheel tightness. Allow material to cool on workbench. JSA for Welding Cutting grinding JSA for welding of HVAC Pipes JSA for the fixing embedded Plate JSA for operation of jack hammering on generator footing JSA for J mobilization of crane welding cutting and grinding and Air Blowing of spools in process area JSA for mobilization of crane erection of spools and welding cutting and grinding and tie in on existing spools.

And 30 minutes after welding cutting and grinding. Cutting grinding and welding job 3. 17 Risk Rating Step Environmental HazardsImpacts.

Job Safety Analysis Sheet JOB DESCRIPTION. Power cable to be checked prior to grinding welding operations for no damage. Job Safety Analysis Job Steps.

Mobilization of Equipment 2. Check conditions of grinding wheel and appropriate RPM. Verify the guard is tight and appropriate for the job.

Foot injury from dropping the tool Rest the tool on the bench. Chalk mark welded area Hot 7. During weldingcutting operations proper welding gloves and a full-face UV-ray protective shield shall be worn to prevent injuries to the operator.

High Pressure air Flying objecteye injuries. Ad China Sale Welding Machine.

Job Safety Analysis Form Hazard Analysis Job Analysis Task Analysis

Chain Link Drag Mat Cheapest Drag Mat With Effectiveness Garden Tractor Attachments Diy Driveway Diy Lawn