Padeye Welding All padeyes must be welded to the primary struture by use of full penetration welds. If the padeyes are only subjected to low fatigue utilisation then full pen welds will be a waste of time in production and it might.
Aisi 316 Stainless Steel Flat D Shackle With Bar 316 Stainless Steel Stainless Steel Stainless
Full pen welds will match the strength of your padeyes provided you require a qualified welding procedure for these welds.
Welding pad eyes. Compared to your CSA padeye our lifting lug has 8 more weld length which adds 30 minutes a labor rate of 105hr and cost is about 15 higher for our lifting lug compared to the CSA padeye. Each pad eye consisted basically of a 50mm thick vertical plate measuring approximately 2m x 1m which contained a hole reinforced by rings welded to each side of the plate. Weld on lifting eyes are permanent lifting points used to connect slings and rigging hardware.
Moreover no stitch welding should be permitted in the active area of the weld length Fig 2. The welds to the ground material shall be full penetration welds and the quality of the ground plate with tensile stress must be Z-quality. It meets the requirements of Military Specification MS-51930A.
Buy View Add to wishlist. Crosby 264 Pad Eyes Crosby 264 Pad Eyes Quic-Align. Tack weld corners and remove welding square to fi nish the welding process.
DNV pad eyes options available too. At Bishop Lifting Products our Solutions division is able to fabricate flat beveled and plate mounted pad eyes to fit any lifting device needed. Crosby 405 Lifting Eyes Crosby 405 Lifting Eyes Pad Eyes.
Pad Eye Strengths. Yoke Grade 8 Weld-on Lifting Point. Lifting-eyes known as pad eyes were welded into the top corners of a module for lifting the module on to an offshore platform.
It is good practure to extend the base of the padeye to pass it completely through the structural member which it is connected to. As high quality welding is essential for reasons of security andor safety all welding on padeyes should be carried out by coded welders using approved procedures and certified materials welding rods. Crosby HR-100 UNC Pivot Hoist Ring Crosby HR-100 UNC Pivot Hoist Ring.
Buy View Add to. A pad eye lug can be designed with some reserve strength by taking into account a side load in the weak axis. It is good practure to extend the base of the padeye to pass it completely through the structural member which it is connected to.
Use IMIs 90 welding square to position and hold padeyes in place while welding them to desired product or structure. For this reason a weld joint factor of 09 to 10 is reasonable for padeyes. The Crosby Group Inc.
Welding Welding All padeyes must be welded to the primary struture by use of full penetration welds. Weld-on Lifting Eyes and Welded Down Lashing Points Weld-on Non Swivel Lifting Lashing Hooks Eye Bolts LiftingSafety Weld-on Non-Swivelling and Non-Pivoting Lifting Eyes and Weld Down Lashing Points LiftingSafety Weld-on Pad Eyes Proof Load Range from 2t to 50t. The pad eyes were welded to the plates using full penetration welds and 8-mm joints.
It is widely used on farm machinery trucks steel hulled marine vessels and material handling equipment. Technical Data Sheet 01252001 weld quality and size a Working Load Limit is not provided for pad eyes. Pad Eye Size Approximate Capacity 0 650 lbs.
Item added to wishlist. The welds were then tested using magnetic particle inspection and ultrasound the most com-. Welded into place where needed.
Crosby Pad Eyes are lifting eye bolts for welding on to a suitable support structure to create a certified lifting point they are designed to be attached to any structure equipment vehicles or machinery in which there is a need or desire for an eye without the drilling andor threading required for an threaded shank eyebolt. The load direction on the pad eyes are normally 30 degrees angle from vertical but custom pad eyes can be designed and analysed for any angle if required. An approximate strength level for the eye of the pad eyes is.
W Pad weld size W Lug weld size The width of the lug is 2R The width of the gusset is a minimum of 2R. The Crosby Pad Eye S-264 is Forged from 1035 Carbon Steel for excellent welding quality. Crosby SL-150 Slide-Loc Crosby SL-150 Slide-Loc Crosby SL-150M Slide-Loc Crosby SL-150M Slide-Loc Specialty Hoist Rings.
Item removed from wishlist.
First Aid Posters Safety Poster Shop Part 3 First Aid First Aid Poster First Aid Tips
Iso Block Cast Padeye Jpg Containers For Sale Container Iso Container
Amazon Com California Sun Sail Shade Galvanized Hardware Padeye Patio Lawn Garden Sun Sail Shade Shade Sail Offset Patio Umbrella
Aisi 316 Stainless Steel Lift Pad Eye 316 Stainless Steel Steel Stainless
Pin On Boat Product
Arc Eye First Aid Severe Headache How To Remove Medical
Aisi 316 Stainless Steel Din1480 Turnbuckle Eye Hook 316 Stainless Steel Steel Stainless Steel
Round Base Pad Eye Stainless Steel Fittings Stainless Hardware
Designed With A Fast Aggressive Diamond Segment And Strong Cast Iron Steel Body For Calibration And Grinding On Automatic Polishin Iron Steel Cast Iron It Cast
0 comments:
Post a Comment